Water Well Drilling in Kerrville, TX
Kerrville Well Drilling drills, cases, and completes new water wells across Kerrville, Ingram, and Kerr County, Texas. We handle the whole job: the permit with the Headwaters Groundwater Conservation District, the drilling through hard Hill Country limestone, the casing, the pump and pressure tank, the wiring, and the water test that finishes it. We are a licensed and insured Texas water well contractor, and every well we drill is registered with the district that covers your land.
Most of the calls we get start the same way. Someone buys raw land on the plateau, past the end of any city water, and the house cannot exist until it has a well. Out here there is no line down the road to tie into. The water comes from deep in the rock or it does not come at all. We drill the well that makes the property livable, and we build it to survive the droughts this country is known for.
Deep Rock Is the Job Here
The Edwards-Trinity plateau under Kerr County is hard limestone, and reliable water is often deep. A well that catches the first shallow water it finds is the well that fails in a dry summer, so we drill down to a zone that holds through a drought, frequently into the lower Trinity. That means real depth, real casing, and a rig that works harder per foot than it would in soft ground. The hard rock and the depth are why Hill Country wells cost what they do, and why cutting the depth short to save money is a false economy that buys a re-drill.
The Order of Work on a New Well
We read the ground first, looking at what nearby wells did and how deep they had to go. Then we permit the well with the Headwaters district and wait for it to clear. Then the rig drills the hole and we case it to hold the wall and seal out surface water. Once we reach a sound producing zone we set the pump deep, plumb the pressure tank or storage, wire the controls, and test the water and the flow before we call it done. Skipping the front of that sequence is how a well ends up short of water in August.
What You Decide, and When
How many people and how much irrigation the well has to serve, before we size the pump. Where the well sits, at layout, held to the district spacing from lines, septic, and other wells. Casing depth and pump size, which the rock and the water zone mostly settle for us. Access for the rig, before the drill date, because plateau lots are often steep and rocky. Everything else follows the ground and the permit. Call (830) 555-0173.
How deep are wells around Kerrville?
Deeper than most of Texas, and that is the plain truth of drilling on the plateau. The Edwards-Trinity aquifer under Kerr County can give water at moderate depth in places, but reliable, drought-proof water often means drilling down into the lower Trinity, and that can run from several hundred to well over a thousand feet. The hard limestone slows the drilling too. We read the neighboring wells and drill to a zone that will hold up in a dry year, not just to the first water we touch.
Why does a Kerrville well cost more than a well in flatter country?
Two reasons, both about the rock. First, depth. Dependable water on the plateau is often deep, so there is more hole and more casing than a shallow well elsewhere. Second, the rock is hard limestone, which is slower to drill through, so the rig spends more time per foot. Those two together are why a Hill Country well sits at the higher end. We price it after we know the target depth, because on this ground the depth is the price.
Do I need a permit to drill in Kerr County?
Yes. Kerr County is covered by the Headwaters Groundwater Conservation District, and a new well needs a permit and a licensed driller before drilling starts. The district sets spacing and registers the completed well. We are a licensed Texas driller, we file the permit, and we drill to the district rules. Wells in the neighboring counties fall under their own districts, and we file with whichever one covers your parcel.
Will a new well survive a drought?
That is the whole point of drilling it right out here. The Hill Country is drought-prone, and a shallow well finished in the first water it hits is the one that goes dry in a bad summer. We drill to a deeper, more reliable zone and set the pump low enough to keep water over it through a dry stretch. A well built for the drought costs more up front and saves you a re-drill later. We build for the dry year, not the wet one.
What does a complete well cost here?
On current Hill Country jobs, a complete deep-rock well, meaning the drilling, casing, pump, pressure tank, and wiring, commonly runs from roughly twelve thousand into the mid thirty thousand range. The depth and the hard rock push Kerr County wells toward the higher end of what Texas wells cost. We do not quote it blind. We read the ground, estimate the target depth, and price the well off that.